Warning and Caution Safety and Regulatory Notice DHV Board Components DWN Board Components Intel assumes no responsibility for any errors.

Author:Karr Gorr
Country:Turks & Caicos Islands
Language:English (Spanish)
Published (Last):17 May 2014
PDF File Size:1.39 Mb
ePub File Size:7.32 Mb
Price:Free* [*Free Regsitration Required]

Quick Reference This guide is written for technically qualified personnel with experience installing and configuring desktop boards. Warning and Caution DHV Board Components The Intel Web site also includes telephone numbers and billing charges, if applicable, for Intel customer support.

Intel Corporation Intel makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Intel assumes no responsibility for any errors that may appear in this document. Intel makes no commitment to update nor to keep current the information contained in this document.

No part of this document may be copied or reproduced in any form or by any means without prior written consent of Intel. Intel and Pentium are trademarks and registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Other names and brands may be claimed as the property of others.

Copyright , Intel Corporation. All rights reserved. See the Intel Desktop Boards DHV and DWN Product Guide for all applicable regulatory compliance statements, product certification markings, and safety and electromagnetic compatibility EMC standards and regulations these desktop boards are compliant with. Replacement battery warning label provided: Place the label inside the chassis in an easy-to-see location near the battery but not on the board itself.

Intended uses: This product was evaluated as information technology equipment ITE for home or office use when installed into an appropriate computer chassis. Other end uses or locations may require further evaluation. C AGP connector 1. When installed in the chassis, the shield blocks radio frequency transmissions, necessary to pass emissions EMI certification testing, protects internal components from dust and foreign objects, and promotes correct airflow within the chassis.

Place the shield inside the chassis as shown in the following figure. Press the shield into place so that it fits tightly and securely. If the shield doesnt fit, obtain a properlysized shield from the chassis supplier. Refer to your chassis manual for specific instructions on installing and removing the board.

Secure the board to the chassis standoffs using the screws. The figure below shows the eight mounting holes for the DHV board. The board comes with the processor fan heatsink base.

Follow the instructions below to install the base to the board. Observe the precautions in Before You Begin on page 3. The processor fan heatsink base is secured to the board with four pushpins.

See the location of the processor fan heatsink base mounting holes in the following figure. Align the four fasteners B of the processor fan heatsink RM base with the corresponding holes in the desktop board C.

Gently press the base down until all four corners snap into place. Verify that all four fasteners are fully engaged, then press down each of the four locking pushpins A to fully secure the base to the desktop board.

Lift the processor socket lever. Install the processor so that the corner with the triangle marking A is aligned with the corner where the lever is attached to the socket. Lower the lever back to its original position. To install DIMMs, follow these steps: 1. Turn off all peripheral devices connected to the computer. Turn off and unplug the computer. Remove the computer cover and locate the DIMM sockets. Holding the DIMM by the edges, remove it from its antistatic package.

Make sure the clips at either end of the socket are pushed away from the socket as shown above. Position the DIMM above the socket.

Align the two small notches in the bottom edge of the DIMM with the keys in the socket. Insert the bottom edge of the DIMM into the socket.

Make sure the clips are firmly in place. Replace the computer cover. Place the board component side up on a flat, supportive surface. Locate the AGP connector on the board as shown below. Note that the boards silkscreen C indicates the correct final position of the lever D on the RM. Push the lever end of the RM in the direction of the arrow until the two rearmost tabs E spread over the end of the AGP connector. Do not apply unnecessary pressure to avoid damaging the board.

Follow these instructions to install an AGP card if it has a retention notch. Press down on the card until it is completely seated in the connector and the card retention notch snaps into place below the RM.

Secure the cards metal bracket to the chassis back panel with a screw. The following figure shows the location of the fan connectors. Connect the processors fan heatsink cable to the processor fan connector on the board. Connect the chassis fan cables to the board connectors as shown in the figure below.

Chassis Rear Fan J1B1 3 1. The Intel boxed desktop board package includes two IDE cables. Either cable can connect two drives to the desktop board. The cable will work correctly only when oriented as shown in the figure below.

For correct cable function: 1. Attach the cable end with the single connector A to the board. Attach the cable end with the two closely spaced connectors B to the drives. The BIOS uses the current configuration and passwords for booting. Use this menu to clear passwords.

Learn more about Scribd Membership Home. Much more than documents. Discover everything Scribd has to offer, including books and audiobooks from major publishers.

Start Free Trial Cancel anytime. Mb Intel dhv dwn Quickrefguide Uploaded by Lito Suaco. Document Information click to expand document information Description: Intel motherboard user guide. Date uploaded Apr 19, Did you find this document useful? Is this content inappropriate? Report this Document. Description: Intel motherboard user guide. Flag for Inappropriate Content. Download Now. Related titles.

Carousel Previous Carousel Next. Jump to Page. Search inside document. ByfwwtyrspIhp 1. OM 4. Kenneth Mike. Artistic Origins. Abhishek Jaju. Mo'men Nabil.

Baim Isaac. Jeremiah Pitts. Sivakumar Ravichandran. Greenhouse Mice. Hassam Ahmad. Rishab Chawla. Juris Dela Rosa Urbano. Kamran Khan. John Fletouris.


Mb Intel d845hv d845wn Quickrefguide01

SuperTrak SX Firmware. Fixed the problem that when trying to compress a folder with large amount of data, system hangs and creates timeouts. Fixed the problem that array will go offline during rebuild if one source disk has a bad sector. Fixed problem when host memory size is over 4GB. Improved error handling scheme.


Intel D845WN User Manual



Intel D845WN User Manual – Download


Related Articles