HOW TO INTERFACE 16X2 LCD WITH 8051 MICROCONTROLLER AT89C51 PDF

We use LCD displays for displaying the error messages, etc. Working of Circuit: The crystal oscillator is connected to XTAL1 and XTAL2 which will provide the system clock to the microcontroller the data pins and remaining pins are connected to the microcontroller as shown in the circuit. The potentiometer is used to adjust the contrast of the LCD. You can connect data pins to any port. If you are connecting to port0 then you have to use pull up registers.

Author:Vimi Dogis
Country:Equatorial Guinea
Language:English (Spanish)
Genre:Automotive
Published (Last):12 February 2012
Pages:24
PDF File Size:20.6 Mb
ePub File Size:20.36 Mb
ISBN:192-6-36340-854-3
Downloads:67152
Price:Free* [*Free Regsitration Required]
Uploader:Fezahn



We use LCD display for the displaying messages in a more interactive way to operate the system or displaying error messages etc. Hence, in this project, I will not only give the information of LCD and also provide the code in C language which is working fine without any errors. There are 16 pins in the LCD module, the pin configuration us given below. During the initializing sequence and other commands this pin should low.

A high to low pulse of about ns pulse is given to this pin. So by reading the above table you can get a brief idea how to display a character.

For displaying a character you should enable the enable pin pin 6 by giving a pulse of ns, after enabling the pin6 you should select the register select pin pin4 in write mode. Follow these simple steps for displaying a character or data. To send a command to the LCD just follows these steps:. Commands: There are some preset commands which will do a specific task in the LCD.

These commands are very important for displaying data in LCD. The list of commands given below:. To get the detailed information, Click Here and Download the Datasheet. Coming to the programming you should follow these steps:.

To initialize LCD to the the following instruction and commands are to be embed in to the functions. The programs given below will use above functions and display the complete string which is given by the programmer to display the data.

We have provided two demo codes working properly and easy to understand. Below is a simple code written in assembly using keil.. The code is written for uc.

For info on pin connections or other things,email me- srihariash gmail. Hi…sir am pratibha…we are ding LCD display project we want code and diagram plz give me. Sir I am designing digital presaure measurment display…I am confuse that I give a anlog signal to adc and it convert that into digital and I want to display preesure according to signal applied to the adc how can I do that..??

I want to read real time values from sensors through microcontroller and display it here. Will this code work or if no then can anyone help me with the code in keil vision software. Your email address will not be published.

Table of Contents. Digital Temperature Sensor Circuit. Comments hi…. Wow, this article is good, my sister is analyzing such things, thus I am going to let know her.

This is the best code I found over internet. Leave a Reply Cancel reply Your email address will not be published. RS is the register select pin used to write display data to the LCD characters , this pin has to be high when writing the data to the LCD. Enable pin is for starting or enabling the module. DB0-DB7 Data pins for giving data normal data like numbers characters or command data which is meant to be displayed.

CHRISTIE ROADSTER HD12K PDF

Interfacing 16×2 LCD with 8051

It is very important to keep a track of the working of almost all the automated and semi-automated devices, be it a washing machine, an autonomous robot or anything else. This is achieved by displaying their status on a small display module. These modules are replacing seven segments and other multi segment LEDs for these purposes. LCD can be easily interfaced with a microcontroller to display a message or status of a device. A 16x 2 LCD means it can display 16 characters per line and there are 2 such lines. This LCD has two registers. A command is an instruction given to LCD to do a predefined task like initializing, clearing the screen, setting the cursor position, controlling display etc.

KONSTRUKTIONSLEHRE PAHL BEITZ PDF

How to interface 16×2 LCD with 8051 microcontroller (AT89C51)- (Part 6/45)

The module were are talking about here is type number JHDA which is a very popular one. VEE pin is meant for adjusting the contrast of the LCD display and the contrast can be adjusted by varying the voltage at this pin. See the circuit diagram for better understanding. The JHDA has two built in registers namely data register and command register. Data register is for placing the data to be displayed , and the command register is to place the commands.

6922 DATASHEET PDF

How to Interface 16X2 LCD With 8051 Microcontroller?

We use LCD display for the displaying messages in a more interactive way to operate the system or displaying error messages etc. Hence, in this project, I will not only give the information of LCD and also provide the code in C language which is working fine without any errors. There are 16 pins in the LCD module, the pin configuration us given below. During the initializing sequence and other commands this pin should low. A high to low pulse of about ns pulse is given to this pin. So by reading the above table you can get a brief idea how to display a character.

Related Articles